Can You Apply Siser HTV to Tri-Blends?

14

Let’s Talk Tri-Blends (Plus a Brother ScanNCut2 Scan to Cut Data Tutorial!)

Cotton, polyester, cotton/poly blends, and leather are the typical fabrics listed under most Siser heat transfer vinyl application instructions. But, I’m going to let you in on a secret: Siser HTV can go on much more than those fabrics! However if we listed every. single. material. that Siser HTV can be applied to you’d be hard pressed to find application instructions amidst a sea of material types. Included on that secret list of Siser HTV safe materials are tri-blends.

Tri- blends are the ultimate combination of cotton, polyester, and rayon(AKA viscose.) This triple threat t-shirt is breathable, soft, and has a flattering finish. An easy way to spot a tri-blend is by the variegated shades. While not quite thin enough to be a burn out t-shirt, tri-blends aren’t one solid color.

Close up view of a tri-blend t-shirt

Despite the fabric difference, Siser HTV application instructions are business as usual for Tri-Blends. The recommended application instructions for any Siser HTV will give you the best application on tri-blends. No changes necessary! Some other fabrics Siser HTV is safe to be applied to, but are unlisted are: denim, bamboo, hemp, velour, fleece, and burlap.

So can you apply Siser HTV to tri-blends? Yes! Keep reading to see how we apply EasyWeed™ to a tri-blend. Plus learn how to create a cut file from scanned text with the Brother ScanNCut2!

How to Scan and Cut Text with the Brother ScanNCut2

The supplies needed for this EasyWeed™ T-shirt

While the Brother ScanNCut2 has convenient pre-loaded fonts, I’m a font junkie and I like to be able to change it up often. So to be able to use a font that’s not saved on the ScanNCut, you can create a text document with your desired font, and scan a copy of it with the Brother ScanNCut to create a cut file!

When creating your text document it’s important to choose a font that’s not too skinny. The lines need to be thick so 1: the scanner will detect them and 2: the cut lines won’t be too skinny for your cutter. I’m using the font Book Antiqua which usually would be too thin, but choosing the “Bold” option thickened the lines enough for scanning. I placed my document on the ScanNCut Medium Tack mat. If you have the Low Tack mat that would be even better to use, however the Scanning Mat is the best for cases like these. But any of the listed mats will work, so once you have it stuck on, load the mat into the cutter.

Select Scan on the Brother ScanNCut2

Select “Scan”

Select Scan to Cut Data on the Brother ScanNCut2

Select “Scan to Cut Data”

 

 

 

 

Scanning a document copy with the Brother ScanNCut2

Make sure there is enough space in front and behind the ScanNCut 2 for the mat to go all the way through and back out.

Editing cut lines on scanned document

Select the highlighted option to recognize cut lines inside and outside the shapes.

 

 

 

 

 

 

From here you can fine tune your scanned image. If you have varying shades of color in your image you may need to select the gradient bar option to adjust the range of colors the ScanNCut recognizes and converts to cut paths. My font is black, so I had no problems with colors, however I did need to use the “Ignore Object Size” function. This function tells the ScanNCut that everything below a certain object size is not considered a cut path

Select Ignore Object Size on BrotherScanNCut2

Select “Ignore Object Size” to adjust the object size that is recognized and converted to cut lines.

Adjust the object size that is recognized as a cut line

Use the plus and minus options to adjust the object size that will be recognized. Use the zoom option to inspect your cut file.

 

 

 

 

 

 

I lowered the size until I could see the dots of the “I’s” and the insides of the “e’s” were recognized.

Object size is too high to recognize cavities

Before lowering “Ignore Object Size.”

Object size is low enough to recognize cavities

After lowering “Ignore Object Size.”

Now that the cut file is properly set up you can save it directly to the cutter or on a flash drive. I saved mine to the machine and then went back to the home screen so I could navigate to my file. After opening it I can adjust the size and mirror my image.

Mirror image and adjust image size

The Mirror Image option is highlighted in purple.

This file is ready to go! What once started as a piece of paper is now a complete cut file. So let’s turn that cut file into an EasyWeed™ t-shirt!

Place EasyWeed™ on the Standard Mat with the carrier side face down. Cut settings for EasyWeed™ on the Brother Scan N Cut are Blade: 2, Cut Speed: 1, Cut pressure: 2. Load the mat into the Brother ScanNCut2 and select the “Start/Stop” button. When the machine is finished cutting, unload the mat, and weed away the extra vinyl to reveal your words!

Placing EasyWeed™ HTV on the Standard MatWeeding Siser EasyWeed™ heat transfer vinyl

 

 

 

 

Like I mentioned earlier, application instructions don’t vary when it comes to applying on tri-blends. Set your heat press to 305°F with medium pressure. Pre-press your garment for 2-3 seconds. Then set up your EasyWeed™ transfers, cover with a heat transfer cover sheet, and press for 15 seconds. Peel the carrier hot or cold.

Peeling EasyWeed's carrier hot

Peeling EasyWeed’s carrier hot.

Peeling EasyWeed™ carrier cold

Peeling EasyWeed’s carrier cold.

 

 

 

 

 

Heat applying on tri-blends is easy peasy! Plus I can’t wait to use the Brother ScanNCut2’s Scan to Cut Data feature for more projects! If you have any questions about this post please leave them in the comments 🙂

A tri-blend t-shirt decorated with Siser EasyWeed™ HTV
Lily Campau

If you think you're limited to the pre-loaded fonts on the Brother ScanNCut2, well think again! You can use almost any font by using the Scan to Cut Data feature! We'll show you step by step how to transform a copied document to a cut file to a heat transfer vinyl t-shirt!

Share.

About Author

Lily Campau is new to the Heat Transfer Vinyl industry, but she’s always been a crafter who enjoys a wide variety of projects. Her particular passions lie in knitting, sewing, and upcycling home décor. Lily is looking forward to all the vinyl projects to come!

14 Comments

  1. This is the first mention I’ve seen of using Siser HTV on rayon. What about a shirt with 50%, 90% or higher rayon fabric?

    I seem to prefer shirts made with rayon, as it is always what I gravitate towards in stores, and my closet is full of it. I assume that EasyWeed Stretch would work on it but I just started using vinyl and I haven’t purchased any yet.

    • Astrid, a shirt with 50-100% rayon will be fine for heat application. EasyWeed™ Stretch is a great choice, but you could really choose any Siser heat transfer vinyl. Just follow the application and washing instructions.

  2. Pingback: Brother ScanNCut On-The-Go | Siser N.A.

  3. I tried using Siser EasyWeed HTV on a 60% cotton, polyester blend tshirt. The vinyl didn’t adhere. I tried different heat temps and longer amounts of time with no luck. I noticed the shirt tag said “Do not iron decoration.” Could the fabric be coated with something that prevents the vinyl from adhering?

    • Hi Yolanda, if the tag says any variation of “Do No Iron” then the material is most likely not going to work with HTV. The garment can have a resistant coating or sometimes it may scorch under high heat.

  4. So this includes using glitter HTV on tri-blends as well? Application directions for glitter are 320 degrees, firm pressure.

  5. I used siser easyweed stretch on a 95% rayon 5% spandex shirt and it left heat press marks. Any ideas on how to get the marks out or is the shirt ruined?

    • Hi Lauren, unfortunately those marks are probably there to stay. Most rayon won’t have a problem with heat press marks, but some will start to melt beneath the high heat and leave marks. For the future, you can lower your application temperature to about 280°F. Just remember that when you lower the application temperature you need to increase the pressing time. Hope that helps!

    • Hi Phil!

      After you’ve pressed for the recommended time of the material you’re working with you can press for 2 second intervals until you’re able to remove the carrier sheet. You can remove the carrier sheet even if your edges are lifting a little bit. Just cover the applied HTV with a heat transfer cover sheet and press for another 2 seconds to finish it off!

  6. Thank you so much for this post! I just ordered some Siser gold holographic HTV to make a shirt for our upcoming vacation, checked my shirt, and it is a 95% rayon/5% spandex blend! I was SO worried that it wouldn’t transfer properly, but now I see as long as I’m careful, it should be fine. Yay!

Leave A Reply